General Description: This product is a oil based utility primer developed to meet the requirements of an economically priced shop primer.
	Common Usage: Typical substrates include construction equipment, original equipment manufacturing and shop applications. This product offers good barrier protection to final assembly and subsequent application of finish enamels.
	Color: Gray (Also available in Red - #CC-1679)
	Finish: Low Sheen

Finish Coats: Typical topcoats include Anchor #900 series Saf-T-Gard II gloss enamels. Avoid using finish systems cut in any of the stronger solvents such as aromatic or ketone solvents. Each service environment may require a specific coating system or a combination of Anchor products. Consult your Anchor representative for specific job recommendations.

The surface must be clean, dry, and free of all dirt, grease, oil, loose paint, rust, or other contaminants. The surface substrate should be cleaned in accordance with SSPC-SP1. All burrs should be removed and sharp edges or rough weld seams ground down. Where weathered steel is evident and where the substrate has reached rust grade, appropriate chemical cleaning or blasting will be necessary.

	Volume Solids: 46.70%
	Recommended Thickness: 1.6-2.0 mils minimum dry.
	Drying Time:  Temperature To Touch To Recoat Full Cure 75 F / 55% R.H. 40 Minutes Overnight 1 week (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Not Intended For Residential Use, Shop Use Only.
	Actual V.O.C.: 3.42 lbs./gal. (410 g/l)
	Theoretical Coverage: 749 sq.ft./ gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on surface texture and application technique.
	Packaging: 55 Gallon drums, and 5 Gallon pails
	Storage Temperature: Minimum 20F Maximum 110 F
	Chemical Resistance: Alkalis: Fair Acids: Good Water: Good
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 3.9 416 Minimum: 1.6 3.4 468 Maximum: 2 4.3 374
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: This coating is V.O.C. compliant, thin only if necessary with Anchor # J-1131 or #T-50 for spray applications if permitted by federal, state, and local regulations.
	Surface Temperature: Minimum 40 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1200-2200 psi Tip: .011"- .015" Conventional Spray Air Pressure: 60-80 psi Fluid Pressure: 10-20 psi
	Cleanup: Use Anchor #J-1131 or #T-50
	Application Considerations: Spray application is recommended, brush and roller are permitted. Apply in wet coats to avoid dusting. When spraying, use a cross-hatch method, overlapping each pass 50%. Clean spray equipment thoroughly before and after each use. On a derusted surface the application of a dry film thickness of at least 2.0 mils is recommended. Due to the high solids of this product, care should be taken to not overbuild the coating. Applying too much will lengthen the dry time and possibly result in "mudcracking" in the film. Note: When scheduling work, allow for adequate time when adverse weather and precipitation is forecast.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.