Product Profile:
 |
General Description:
A fast drying industrial waterborne acrylic coating that develops a hard finish with
excellent blocking and chemical resistance.
|
|
Common Usage:
This product was developed as an alternative to Alkyd and Lacquer based
coatings for a wide range of application and surface substrates.
|
|
Color: Safety Yellow |
|
Finish: Gloss |
Coating Systems:
|
Primer Coats:
This product can be applied over non-lifting primers, undercoaters or
direct-to-metal to properly prepared surfaces. Consult your Anchor representative
for specific job recommendations.
|
Surface Preparation:
|
Surface should be dry and free of contaminants such as excess dirt, grease or oil.
|
Technical Data:
|
Volume Solids: 37.35% |
|
Recommended Thickness: 1.0-1.4 mils dry per coat. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
25 minutes |
|
1 Hour |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Non-Flat Coatings |
|
Maximum Allowable V.O.C.: 3.2 lbs./gal. (380g/l) |
|
Actual V.O.C.: .76 lbs./Gallon (91 g/l), (1.59 lbs./gal. minus water + exempt materials) |
|
Theoretical Coverage:
599 sq. ft./gallon @ 1 mil dry, assuming no application losses.
Coverage will vary depending on surface texture and application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails, and 1 Gallon cans
|
|
Storage Temperature:
| Minimum 35 F |
|
Maximum 110 F |
|
|
Physical Properties:
|
Abrasion: |
|
Very Good |
|
Weather: |
|
Very Good |
|
|
Chemical Resistance:
|
Solvents: |
|
Very Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.2 |
|
3.2 |
|
499 |
|
Minimum: |
|
1 |
|
2.7 |
|
599 |
|
Maximum: |
|
1.4 |
|
3.7 |
|
428 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Thinning: Thin with water, only if necessary.
|
|
Surface Temperature:
| Minimum 55 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi. |
|
Tip: |
|
.013"-.017" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use a quality nylon or polyester bristle brush. |
|
Roller: Do not exceed a 3/8" nap cover. |
|
|
Cleanup: Use soap and water. |
|
Application Considerations:
This product may be applied by Brush, Roller or Spray. Do not apply when
overnight freeze, rain or dew is imminent. Warm air, moving over the substrate,
will promote drying and improve cure time when less than optimum application
conditions exist.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
