Product Profile:
 |
General Description:
A two component polyvinyl-butyral primer. This is a pre-treatment wash
primer that can be used for etching when sandblasting is not feasible. This
product does not contain chromium or chromium compounds.
|
|
Common Usage:
Aluminum, smooth formed metals such as hot or cold rolled steel, galvanized
surfaces, or other non-ferrous metals.
|
|
Color: Translucent gray |
|
Finish: Flat |
Coating Systems:
|
Finish Coats:
Typical topcoats include epoxies, vinyls, alkyds, urethanes and acrylics.
Consult your Anchor representative for specific job recommendations.
|
Surface Preparation:
|
Surface must be perfectly clean. The surface must be free of all dirt, grease, or
other contaminants, rust or moisture. This product is designed for new and
unpainted surfaces.
|
Technical Data:
|
Volume Solids: 12.23% when Catalyzed |
|
Recommended Thickness: 1/2 mil maximum |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 77 F / 55% R.H. |
|
10 Minutes |
|
30 Minutes |
|
|
|
Architectural and Industrial Maintenance Category: Pre-treatment Wash Primers |
|
Actual V.O.C.: 5.92 lbs./gallon (711 g./l.) |
|
Theoretical Coverage:
391 sq. ft./ gallon @ 1/2 mil dry, assuming no application loss. Coverage will
vary depending on surface texture and application technique.
|
|
Packaging: One gallon kit consists of a one gallon container filled short to accommodate
one quart acid diluent Anchor #CC-1723 B.
|
|
Storage Temperature:
| Minimum 20 F. |
|
Maximum 110 F. |
|
|
Chemical Resistance:
|
Alkalis: |
|
Poor |
|
Acids: |
|
Poor |
|
Water: |
|
Fair |
|
|
Heat Resistance: Flash Point 70 F (T.C.C.) |
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
|
Pot Life: 8 Hours |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
0.1 |
|
0.8 |
|
1564 |
|
Minimum: |
|
|
|
|
|
|
|
Maximum: |
|
|
|
|
|
|
|
|
Mixing: Slowly mix Four (4) parts vinyl wash primer Anchor #CC-1723 A with one part acid
diluent Anchor #CC-1723 B on the job.
|
|
Thinning: Before mixing acid with primer, the primer may be reduced up to 20% with
Anchor #J-1133 thinner.
|
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 90 F. |
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1800-3000 psi. |
|
Tip: |
|
.011 |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
60-80 psi |
|
|
Fluid Pressure: |
|
10-20 psi |
|
|
Cleanup: Use Anchor #J-1133 thinner |
|
Application Considerations:
The mixed material must be used within an 8 hour period. The primer should
then be recoated within 24 hours as this coating has poor weatherability.
Coverage will vary depending on the surface texture and application
technique. This product is most efficient at minimum film thickness, as soon
as the gray color becomes visible, the film build is sufficient.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
