Product Profile:
 |
General Description:
An "Acrylic" emulsion with exceptional leveling, fast drying, and rapid film
hardness development. Dries to a clear, tough, all purpose finish with
superior adhesion to many substrates plus exceptional water and detergent
resistance.
|
|
Common Usage:
For use on interior and exterior wood, trim, cabinets, paneling and furniture.
|
|
Color: Clear |
|
Finish: Semi-Gloss |
Coating Systems:
|
Primer Coats:
No primer necessary. Consult your Anchor representative for specific job
recommendations.
|
Surface Preparation:
|
Apply only over clean, dry and properly prepared surfaces that are free of dirt,
dust, grease, wax, and loose foreign matter.
|
Technical Data:
|
Volume Solids: 21.1% |
|
Recommended Thickness: 2-4 mils dry per coat. Two coats recommended. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 77 F / 55% R.H. |
|
10 Minutes |
|
45 Minutes |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Stains, clear and semi-transparent |
|
Maximum Allowable V.O.C.: 4.6 lbs./gal. (550 g/l) |
|
Actual V.O.C.: .97 lbs./gal. (116 g/l) (2.12 lbs./gal. minus water + exempt materials) |
|
Theoretical Coverage:
338 sq. ft./gallon @ 1 mil dry, assuming no application losses. Coverage will
vary depending on the surface texture and application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans
|
|
Storage Temperature:
| Minimum 35 F |
|
Maximum 110 F, (Store inside, Acri-Lac 2912 must be not be exposed to freezing temperatures) |
|
|
Physical Properties:
|
Abrasion: |
|
Very Good |
|
Flexibility: |
|
Excellent |
|
Weather: |
|
Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
2.0 |
|
9.5 |
|
169 |
|
Minimum: |
|
1.0 |
|
4.7 |
|
338 |
|
Maximum: |
|
3.0 |
|
14.2 |
|
113 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Thinning: Thin with water only if necessary up to one pint per gallon.
|
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi. |
|
Tip: |
|
.011 |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
|
Cleanup: Use soap and water. |
|
Application Considerations:
Spray application only. Material comnes in ready to spray consistency, thin
only if necessary with water until material atomizes at the tip. The coating
should be applied only when the ambient air and surface temperature is
between 50 degrees Fahrenheit and 90 degrees Fahrenheit. Do not apply
when overnight freeze, rain or dew is imminent. Warm air, moving over the
substrate, will promote drying and improve cure time when less than optimum
application conditions exist.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
