General Description: This material is a high-solids modified polyamine cure organic zinc rich epoxy coating that provides a low temperature cure with excellent chemical and solvent resistance. Modified polyamine cured epoxies combine outstanding resistance to solvents, tap and salt water, acids and bases, shock and abrasion.
	Common Usage: Excellent adhesion and flexibility are obtained over metal. This product is a shop and field applied primer for steel.
	Color: Zinc Gray
	Finish: Low Sheen
	Activator Required: Yes, #CC-1739

Finish Coats: This product is specially designed for use in a 3 component system with an epoxy barrier coat (#CC-1514) and a Urethane (#4900 Series) topcoat. Consult your Anchor representative for specifc job recommendations.

SSPC-SP 6 is recommended including removal of all mill scale. Remove any grease, oil, or dirt with solvent or chemical cleaner before sand blasting, in accordance with SSPC-SP 1.

	Volume Solids: 66%
	Recommended Thickness: 2-3 mils recommended
	Drying Time:  Temperature To Touch To Recoat 77 F / 55% R.H. 3 Hours 4 Hours Cooler temperatures and higher humidity will require a longer cure time. However, very rapid cures can be obtained by force drying or baking the epoxy.
	Architectural and Industrial Maintenance Category: Metallic Pigmented Coatings
	Maximum Allowable V.O.C.: 4.2 lbs./gal. (500 g/l)
	Actual V.O.C.: 2.4 lbs/gal. (288 g/l)
	Theoretical Coverage: 1061 sq. ft./gallon @ 1 mil dry, assuming no application losses.
	Packaging: 5 Gallon pails, and 1 Gallon cans
	Storage Temperature: * Store Indoors Minimum 40 F * Store Indoors Maximum 95 F
	Chemical Resistance: Alkalis: Excellent Acids: Excellent Water: Excellent Solvents: Excellent Strong_Solvents: Excellent
	Heat Resistance: 180 F Continuous, 230 F Non-Continuous
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.
	Mix Ratio: 4:1
	Pot Life: 3-4 hours after catalyst is mixed at 70 F. (Keep cool and agitated)

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 2.0 3.0 530 Minimum: 1.0 1.5 1061 Maximum: 3.0 4.5 354
	Mixing: One part Anchor #CC-1739 Catalyst to four parts #CC-1738 Zinc Rich Epoxy. Stir the Catalyst into the Epoxy. Agitation during application is highly recommended.
	Thinning: Thin with Anchor #3905 as needed.
	Surface Temperature: Minimum 40 F Maximum 90 F The surface should be dry and the relative humidity should be below 90%.
	Application Equipment: Airless Spray Pressure: 1800-3000 psi. Tip: .015 Conventional Spray Air Pressure: 75-100 psi. Fluid Pressure: 10-20 psi Brush: Use a high quality natural china bristle brush, for touch up purposes only.
	Cleanup: Clean equipment thoroughly before and immediately after using Anchor #3905.
	Application Considerations: Do not apply when the surface temperature is less than 5 F or 3 C above the dew point. Coverage will vary depending on porosity of the surface and appplication technique. Allow for application losses due to overspray conditions and surface texture.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.