Product Profile:
 |
General Description:
A specially formulated acrylic coating that dry falls in ten (10) feet.
|
|
Common Usage:
Offers excellent adhesion, high light reflectance, and resistance to flash rusting
when applied to interior ceilings, overhead steel, galvanized steel, nonferrous
metals, and concrete. It can be used in overhead areas not subject to direct
weathering such as production facilities, warehouses, and parking garages.
|
|
Color: White |
|
Finish: Low Sheen |
Coating Systems:
|
Finish Coats:
This product is self-priming, however it may be applied over existing coatings
in good condition only. Consult your Anchor representative for specific
job recommendations.
|
Surface Preparation:
|
The surface must be clean, dry, free of contaminants and mold release agents.
On previously painted surfaces, be sure stains and imperfections will not bleed
through coating. New or old surfaces need not be primed unless variance in
color is substantial. Glossy surfaces should be sanded or flattened to create
the surface profile necessary for good adhesion.
|
Technical Data:
|
Volume Solids: 29.11% |
|
Recommended Thickness: As required by job specifications. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
30 Minutes |
|
1 Hour |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Dry Fog Coatings |
|
Maximum Allowable V.O.C.: 3.3 lbs./gal. (396 g/l) |
|
Actual V.O.C.: .04 lbs./gal. (5 g/l) (.14 lbs./gal. minus water + exempt materials) |
|
Theoretical Coverage:
467 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will
vary depending on surface texture and applicaation technique.
|
|
Packaging: Five (5) gallon pails only
|
|
Storage Temperature:
| Minimum 40 F |
|
Maximum 110 F |
|
|
Physical Properties:
|
Abrasion: |
|
Excellent |
|
Weather: |
|
Excellent |
|
Corrosion: |
|
Excellent |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
2.0 |
|
6.9 |
|
233 |
|
Minimum: |
|
1.0 |
|
3.4 |
|
467 |
|
Maximum: |
|
3.0 |
|
10.3 |
|
156 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Surface Temperature:
| Minimum 40 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1800-2400 psi |
|
Tip: |
|
.015"-.021" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-60 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use high quality synthetic nylon bristle brushes. |
|
Roller: Use 3/8" natural lambswool roller covers |
|
|
Cleanup: Use soap and water. |
|
Application Considerations:
The material comes in ready to spray consistency, thin only if necessary
with water until the material atomizes at the tip. The orifice size depends
upon the type of unit and the experience of the applicator with this type of
product.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
