General Description: This product is a water soluble pure acrylic masonry sealer.
	Common Usage: It effectively seals concrete floors for easy cleaning and protects substrate staining from oils, water, mild acid and alkalis. It has a milky white appearance which dries quickly to a clear. It can also be used as a masonry conditioner prior to top-coating on exterior vertical masonry.
	Color: Clear
	Finish: Low Sheen

Finish Coats: Consult your Anchor representative for specific job recommendations.

The surface must be dry and free of any contaminants that would hinder the performance such as dirt, oils, excessive efflorescence or chalk, form release or curing agents and any loose paint by scraping, wire brushing or pressure washing. Masonry must be cured 28 days. Repair all structural defects such as cracks, breaks or other flaws prior to application. All smooth uncoated concrete must be etched with a 5% solution of muriatic acid and thorouoghly rinsed if water beads rather than soaks into the surface. All floors should be washed with a non-soapy detergent such as T.S.P. (Tri-Sodium-Phosphate) and thoroughly rinsed. The surface should be checked with litmus paper or a pH pencil to assure a pH of 7-8. If pH is not in range, the surface must be rinsed until a neutral pH is attained. Test moisture on floors by taping a 3'X3' sheet of plastic to the floor overnight. If moisture is present under the plastic, do not apply sealer until moisture is eliminated.

	Volume Solids: 19%
	Recommended Thickness: 1.6-2.0 mils dry per coat.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 20 Minutes 11/2 Hours (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Waterproofing and Treatments
	Maximum Allowable V.O.C.: 5.0 lbs./gal. (600 g/l)
	Actual V.O.C.: .74 lbs./gal. (89 g/l) (2.63 lbs./gal. minus water + exempt materials)
	Theoretical Coverage: 305 sq. ft./gallon @ 1 mil dry. Coverage will vary depending on the porosity of the surface and the application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails and 1 Gallon cans
	Storage Temperature: Minimum 35 F Maximum 110 F
	Physical Properties: Abrasion: Good Water: Excellent
	Chemical Resistance: Alkalis: Very Good
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 9.4 170 Minimum: 1.6 8.4 190 Maximum: 2.0 10.5 153
	Mixing: Stir thoroughly.
	Thinning: Do not thin for application.
	Surface Temperature: Minimum 50 F Maximum 90 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1200-2200 psi. Tip: .011"- .015" Conventional Spray Air Pressure: 40-70 psi. Fluid Pressure: 10-20 psi Brush: Use a quality synthetic or nylon bristle brush. Roller: Do not exceed a 3/8" nap roller cover
	Cleanup: Use soap and water.
	Application Considerations: This product can be applied by brush, roller or spray. Do not overbrush or roll to avoid bubbling. Apply one coat over preciously coated surfaces and two coats over uncoated floors. If previously coated floor is high gloss or a built up coating, it is recommended to de-gloss to assure good adhesion. Do not overbuild this coating as delamination, wrinkling, and/or extremely slow drying times can occur. This product will not prevent tire marks from occuring.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.