General Description: This 100% acrylic high gloss waterborne enamel provides good interior and exterior durability, gloss and tint retention, block and print resistance, ease of stain removal and resists yellowing with excellent adhesion to repainted surfaces including aged alkyds.
	Common Usage: This product is typically used on surfaces such as cabinets, doors, walls, and trim for residential and commercial buildings, and schools.
	Color: White, Black and Custom colors
	Finish: High Gloss

Primer Coats: Normally, prime with Anchor #3601 Exterior Latex Primer and #P-1507 undercoater for interior purposes. Consult your Anchor representative for specific job recommendations.

Paint only over clean and dry surfaces. Remove all loose paint, oil, grease, dirt, chalk or other contaminants that would hinder the performance of the coating. Mildew must be killed by scrubbing with a solution of a non-soapy detergent such as T.S.P. (Tri-Sodium Phosphate), a 10% solution of household bleach and warm water. Thoroughly rinse affected area and let dry prior to painting. Repair all damaged areas and repair any cracks or splits with appropriate caulk or filler. Glossy surfaces should be sanded. On unfinished porous surfaces such as concrete block, a block filler should be used prior to priming.

	Volume Solids: 33.42% -varies by color
	Recommended Thickness: 1.6-2.0 mils dry per coat. Two coats recommended.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 2 Hours 4 Hours (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Non-Flat Coatings, Exterior
	Maximum Allowable V.O.C.: 3.2 lbs./gallon (380g/l)
	Actual V.O.C.: .70 lbs./gal. (84 g/l) (1.68 lbs./gal. minus water + exempt materials) - varies by color
	Theoretical Coverage: 536 sq. ft./gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on the color, surface texture and application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans.
	Storage Temperature: Minimum 35 F Maximum 110 F
	Physical Properties: Abrasion: Excellent Flexibility: Excellent Weather: Excellent
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 4.8 298 Minimum: 1.6 4.3 335 Maximum: 2.0 5.3 268
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: Thin with water only if necessary up to one pint per gallon.
	Surface Temperature: Minimum 50 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1800-2400 psi Tip: .015"-.017" Conventional Spray Air Pressure: 40-70 psi. Fluid Pressure: 10-20 psi Brush: Use high quality synthetic or nylon bristle brushes. Roller: Use 1/4" lambswool covers.
	Cleanup: Use soap and water.
	Application Considerations: Brush, Spray or roll. Strain material before spraying. Backroll after spraying. Check color prior to applying as Anchor cannot be responsible for color dissatisfaction after application. Always apply into rather than away from wet edge, overlapping each pass 50%. Avoid touching up, rolling or brushing back into paint more than ten minutes after applying. Touch up when paint is completly dry. Allow to cure ten days before cleaning newly painted surfaces.
	Touch Up: Proper touch-up is accomplished by applying a thin coat of this product over a well coated surface using the same method of application as used to apply the finish coat, that is, spray over spray, roller over roller. If the finish coat is sprayed, it is also possible to spray a small amount into an empty container, then touching up with a foam brush. Touch up should be done within 5 degrees of the original temperature.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.