General Description: A low V.O.C. Acrylic Urethane finish (two component) providing very high gloss with excellent physical properties such as abrasion and chemical resistance, flexibility and weatherability.
	Common Usage: This product is targeted for applications such as bridges, storage tank exteriors, farm and shop equipment, and heavy machinery.
	Color: White, Clear and to meet standard
	Finish: High Gloss
	Activator Required: Anchor #4906 Activator

Primer Coats: Primer will be determined by service environment and job specifications. Consult your Anchor representative for specific job recommendations.

New Work: For best performance on steel, the surface should be blasted to SSPC-SP6 or SSPC-SP10, including the removal of all mill scale. Prior to blasting, remove all flux and scab from welding and grind smooth all rough weld seams and sharp edges. Remove any grease, oil, or dirt with solvent (SSPC-SP1) or chemical cleaner before blasting. The surface should be coated within 24 hours after blasting. Apply over properly primed surface as detailed by applicable specifications. Old Work: Substrate must be clean, dry and thoroughly degreased in accordance with SSPC-SP1 standards. All damaged areas should be repaired and existing paint should be in good condition. This coating may be applied over most old coatings in sound condition. Check the existing paint by applying on a trial patch and observe overnight for lifting, softening, or wrinkling. If this occurs, the existing paint must be removed or a compatible barrier primer must be applied first. Glossy surfaces should be sanded or brush blasted for best performance.

	Volume Solids: 57.03% (Mixed) -varies by color
	Recommended Thickness: 1.1-1.7 mils dry (Number of coats and thickness requirements will vary with substrate, application method and service equipment)
	Drying Time:  Temperature To Touch To Recoat Full Cure 75 F / 55% R.H. 4 hours 8 hours 7 Days (Accelerator Available, CC-150 - 4oz./ gal)
	Architectural and Industrial Maintenance Category: Industrial Maintenance Coatings
	Maximum Allowable V.O.C.: 3.8 lbs./gal. (450 g/l)
	Actual V.O.C.: 2.9 lbs./gal. (348 g/l) when mixed with activator -varies by color
	Theoretical Coverage: 915 sq. ft./ gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on the color, application technique, porosity and design of the substrate.
	Packaging: A 1 gallon kit consisting of a 1 gallon container of urethane partially filled to accommodate a 1quart container of activator. When mixed, it yields 1 gallon. The 5 gallon kit consists of a 5 gallon container of urethane, partially filled to accommodate a 1 gallon container of activator. When mixed, it yields 5 gallons.
	Storage Temperature: Minimum 20 F Maximum 110F
	Chemical Resistance: Alkalis: Excellent Acids: Very Good Water: Excellent Solvents: Excellent Salt: Excellent Immersion: Not recommended
	Heat Resistance: 350 F Intermittent, 250 F Continuous (Dry)
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.
	Mix Ratio: Four parts Urethane to one part #4906 Activator.
	Pot Life: 2 Hours @ 77 F (Keep cool and agitated)

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.5 2.6 610 Minimum: 1.0 1.8 915 Maximum: 2.0 3.5 457
	Mixing: When mixing urethane and activator, hand or mechanically agitate being careful not to mix so fast that air is entrapped.
	Surface Temperature: Minimum 50 F The surface should be dry and the relative humidity should be no greater than 60%
	Application Equipment: Airless Spray Pressure: 1200-2200 psi Tip: .011"-.015" Conventional Spray Air Pressure: 60-80 psi Fluid Pressure: 10-20 psi Use pressure pot with dual regulators,. Air Hose: 3/8 I.D. hose Spray Gun: Use a .070" tip, appropriate air cap and oil/water seperator. Brush: High Quality Pure China Bristle. Roller: Short nap mohair roller with Phenolic Core.
	Cleanup: Use Anchor #T-3M MIBK solvent.
	Application Considerations: This product is moisture sensitive. Do not apply when the surface temperature is within 10 F of the dew point or when freeze, rain, or dew is forecast within 72 hours. Apply first coat as a mist or tack coat prior to subsequent finish coats as specified by job requirements.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.