General Description: A low odor, linseed modified, deep penetrating, oil wiping stain that produces unique tones, enhancing the natural beauty and texture of the wood. Because Richwood stains are so forgiving and easy to apply, the average homeowner can achieve professional results.
	Common Usage: Typical surfaces for application are unfinished interior wood trim, cabinets, paneling, doors, furniture and floors.
	Color: Standard wood tones

Finish Coats: This product can be topcoated by either solvent or waterborne lacquer, varnish, or polyurethane coatings. Consult your Anchor representative for specific job recommendations.

The surface must be free of all dirt, grease, oil, moisture, or previously applied coatings and finishes before application. The surface should also be sanded to avoid roughness in finish.

	Volume Solids: 37.79% -varies by color
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 1 Hour 8 Hours (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Stains, clear and semi-transparent
	Maximum Allowable V.O.C.: 4.6 lbs./gal. (550 g/l)
	Actual V.O.C.: 4.09 lbs./gal. (490.8 g/l) -varies by color
	Theoretical Coverage: 606 sq. ft./gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on color, the surface texture and application technique.
	Packaging: 5 Gallon pails, 1 gallon cans, 1/4 gallon quart cans.
	Storage Temperature: Minimum 20 F Maximum 110 F
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 4.8 337 Minimum: 1.6 4.2 379 Maximum: 2.0 5.3 303
	Mixing: Stir thoroughly and frequently during application.
	Thinning: Use Anchor #J-1112.
	Surface Temperature: Minimum 50 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Pressure: 1200-2200 psi. Tip: .011"-.013" Conventional Spray Air Pressure: 40-70 psi. Fluid Pressure: 10-20 psi Brush: Use a high quality natural china bristle brush.
	Cleanup: Use Anchor #J-1112.
	Application Considerations: This coating can be applied by brush, spray or by wiping with a white knit cotton rag. Apply in a full wet coat. One coat should suffice, but an additional coat can be applied if a deeper tone is desired. If spraying, follow by wiping off excess with a clean white knit cotton rag. Test color on an inconspicuous area. Color and depth will vary depending on the type of wood. Dried runs or overlaps can be corrected by re-wetting a rag with the stain and rubbing the affected area. Warning: Rags, steel wool, waste or other media soaked with this stain may spontaneously catch fire if improperly discarded. Immediately after use, place any media containing this stain in a sealed water-filled metal container.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.