Product Profile:
 |
General Description:
This polyurethane varnish can meet many requirements for interior and
exterior applications where a hard, mar resistant finish is needed. It will not
soften from heat and also resists abrasion, weather, water spotting, fruit
acids, oils, gasoline, humidity, etc.
|
|
Common Usage:
This product is easy to work with and flows well over floors, cabinets, trim or
other suitable wood surfaces.
|
|
Color: Clear |
|
Finish: High Gloss |
Coating Systems:
|
Primer Coats:
Best results can be obtained over cabinets, trim, floors or other interior
surfaces by applying Fin-Seal #1109 prior to using this product. Consult your
Anchor representative for specific job recommendations.
|
Surface Preparation:
|
The surface should be clean and dry and free from any contaminants.
Remove all grease, dirt, dust, etc. with detergent or solvent cleaner. Rinse
thoroughly and allow to completely dry prior to coating.
|
Technical Data:
|
Volume Solids: 43.02% |
|
Recommended Thickness: 1.6-2.0 mils dry per coat. Two coats recommended. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
2 Hours |
|
12 Hours |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Varnishes |
|
Maximum Allowable V.O.C.: 3.75 lbs./gal. (450 g/l) |
|
Actual V.O.C.: 3.74 lbs./gal. (449 g/l) |
|
Theoretical Coverage:
690 Sq. Ft./ Gallon @ 1 mil dry, assuming no application losses. Coverage
will vary depending on surface texture and application technique.
|
|
Packaging: 55-gallon drums, 5 gallon pails, one gallon cans, and quart cans.
|
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110 F |
|
|
Physical Properties:
|
Abrasion: |
|
Excellent |
|
Flexibility: |
|
Good |
|
Weather: |
|
Very Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.8 |
|
4.2 |
|
383 |
|
Minimum: |
|
1.6 |
|
3.7 |
|
431 |
|
Maximum: |
|
2.0 |
|
4.6 |
|
345 |
|
|
Mixing: Stir thoroughly and frequently during application.
By mixing one part #1170 to one part J-1112 thinner, this product will make
an excellent sealer on new or unpainted wood.
|
|
Thinning: Use Anchor #J-1112 thinner, only if necessary.
|
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi |
|
Tip: |
|
.011"-.013" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use high quality natural china bristle brushes. |
|
|
Cleanup: Use Anchor #J-1112. |
|
Application Considerations:
Brush or spray preferred. Apply in full, even, wet coats.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
