Product Profile:
 |
General Description:
A quick drying sealer which offers good film hardness and non-porosity.
|
|
Common Usage:
This product seals unfinished woodwork, trim, furniture and cabinets.
Top-coating not required but if desired, can be topcoated with #1170 Gloss
polyurethane finish. Not for use on floors. Indoor Use Only.
|
|
Color: Clear |
|
Finish: Semi-Gloss |
Coating Systems:
|
Primer Coats:
Consult your Anchor representative for specific job recommendations.
|
|
Finish Coats:
Consult your Anchor representative for specific job recommendations.
|
Surface Preparation:
|
The surface should be clean and dry and free from any contaminants.
Remove all grease, dirt, dust, etc. with non-soapy detergent or solvent
cleaner. Allow to completely dry prior to coating.
|
Technical Data:
|
Volume Solids: 31.47% |
|
Recommended Thickness: 1.6-2.0 mils dry. Two coats recommended for Semi-Gloss finish. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
10 Minutes |
|
30 Minutes |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Sanding Sealers |
|
Maximum Allowable V.O.C.: 4.6 lbs./gal. (550 g/l) |
|
Actual V.O.C.: 4.4 lbs./gal. (528g/l) |
|
Theoretical Coverage:
505 Sq. Ft./ Gallon @ 1 mil dry, assuming no application losses. Coverage
will vary depending on surface texture and application technique.
|
|
Packaging: 55-gallon drums, 5 gallon pails, one gallon cans, and quart cans.
|
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110 F |
|
|
Physical Properties:
|
Abrasion: |
|
Good |
|
Flexibility: |
|
Good |
|
Weather: |
|
Interior Use Only |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.8 |
|
5.7 |
|
280 |
|
Minimum: |
|
1.6 |
|
5.1 |
|
315 |
|
Maximum: |
|
2.0 |
|
6.4 |
|
252 |
|
|
Mixing: Stir thoroughly and frequently during application.
|
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi |
|
Tip: |
|
.011"-.013" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi. |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use high quality natural China Bristle brushes. |
|
Roller: Use a high quality lambswool roller cover . |
|
|
Cleanup: Use Anchor #J-1112 thinner. |
|
Application Considerations:
This product can be applied by Brush, Roller or Spray. Fin Seal should be
lightly sanded between coats for smoother, richer look. Apply in full, wet
coats to avoid laps or dusting. Succeeding coats should be applied within 2
hours, or after 24 hours to avoid lifting of previous coat. If a gloss finish is
desired, apply one coat of Fin Seal. Lightly sand to smooth surface and
remove excess dust with a tack cloth. Then topcoat with #1170 Poly-U Super
Spar Gloss Varnish. Alternatively, if desired, apply one coat of Fin Seal,
lightly sand and remove excess dust with a tack cloth. Then apply a second
coat to acheive a semi-gloss effect.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
