Product Profile:
 |
General Description:
A 100% pure acrylic emulsion maintenance/shop primer that develops
barrier corrosion resistance, normally associated only with solvent-borne
primers.
|
|
Common Usage:
These primers offer excellent adhesion to various substrates such as
structural steel, aluminum, galvanize, concrete, masonry, and wood.
|
|
Color: White, Gray, and Red |
|
Finish: Low Sheen |
Coating Systems:
|
Finish Coats:
Typical topcoats include waterborne enamels such as Anchor #2800 Series
and many alkyd enamels. Consult your Anchor representative for
specific job recommendations.
|
Surface Preparation:
|
Apply only over clean, dry and properly cured surfaces that are free of cutting
solutions, form release agents, dirt, loose foreign matter and moisture. On
structural steel, the substrate shall be thoroughly degreased in accordance
with SSPC-SP1 standards. All burrs should be removed and sharp edges or
rough weld seams should be ground down. All rust and mill scale should be
removed as required by SSPC-SP6 surface preparation (minimum). For
bridge construction, SSPC-SP5 is recommended.
|
Technical Data:
|
Volume Solids: 40.86% -varies by color |
|
Recommended Thickness: 3 mils dry for maximum performance. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
30 Minutes |
|
2 Hours |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Primers and Undercoaters |
|
Maximum Allowable V.O.C.: 2.9 lbs./gal. (350 g/l) |
|
Actual V.O.C.: .54 lbs./gal. (65 g/l) (1.22 lbs./gal. minus water + exempt materials) - varies by color |
|
Theoretical Coverage:
656 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will
vary depending on color, the surface texture and application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails and 1 Gallon cans
|
|
Storage Temperature:
| Minimum 35 F |
|
Maximum 110 F |
|
|
Chemical Resistance:
|
Alkalis: |
|
Excellent |
|
Acids: |
|
Moderate |
|
Water: |
|
Excellent |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
3.0 |
|
7.3 |
|
218 |
|
Minimum: |
|
2.0 |
|
4.9 |
|
328 |
|
Maximum: |
|
4.0 |
|
9.8 |
|
163 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Thinning: Thin with water.
|
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 90 F |
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1800-2400 psi |
|
Tip: |
|
.015"-.019" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
60-80 psi. |
|
|
Fluid Pressure: |
|
10-20 psi. |
|
|
Cleanup: Use soap and water. |
|
Application Considerations:
Spray recommended. Do not apply when overnight freeze, rain or dew is
forecast. NOTE: During Conditions of high humidity or moist air, allow for
a much longer cure time. Warm air, moving over the substrate, will
promote drying and improve cure time when less than optimum application
conditions exist. When applying this coating by roller application, extra
attention to detail is necessary to avoid pinholes.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
