General Description: A unique resin that consists of 30% Silicone resin incorporated into an alkyd. This addition adds a much longer coating life through slower erosion. Due to the incorporation of silicone increasing gloss and color retention, three or four times the longevity can be realized over pure alkyds.
	Common Usage: Heavy equipment, structures, many types of storage tanks, transport vehicles, etc.
	Color: White or Custom colors
	Finish: High Gloss

Primer Coats: Anchor #1600 or #1730 Series Rust Inhibitive Primers. Consult your Anchor representative for specific job recommendations.

At minimum, the substrate should be cleaned in accordance with SSPC-SP1. All burrs should be removed and sharp edges or rough weld seams should be ground down. Where weathered steel is applicable and where the substrate has reached rust grade, appropriate chemical cleaning or blasting will be necessary. This product is designed to applied over a barrier primer or intermediate coats. When not feasible, this product can be applied directly over the substrate making sure a maximum millage is achieved.

	Volume Solids: 44.63% -varies by color
	Recommended Thickness: 1.6-2.0 mils per coat. Two coats recommended.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 1 Hour 8 Hours (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Industrial Maintenance coatings
	Maximum Allowable V.O.C.: 3.8 lbs./gal. (450 g/l)
	Actual V.O.C.: 3.5 lbs./gal. (427 g/l) -varies by color
	Theoretical Coverage: 717 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will vary depending on color, surface texture and application technique.
	Packaging: 5 Gallon pails and 1 Gallon cans
	Storage Temperature: Minimum 20 F Maximum 110 F
	Chemical Resistance: Alkalis: Fair Acids: Good Water: Good
	Heat Resistance: (Dry Heat) 350 F Continuous, 400 F Intermittent
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 4.0 398 Minimum: 1.6 3.6 448 Maximum: 2.0 4.5 358
	Mixing: Stir thoroughly,making sure no pigment remains on the bottom of the can.
	Thinning: Use Anchor #J-1131 or #J-34 Fine Finish Blend.
	Surface Temperature: Minimum 40 F Maximum 110 F The surface should be dry and the relative humidity should be less than 85%.
	Application Equipment: Airless Spray Use appropriate tip and pressure for equipment, technique, and weather conditions. Pressure: 1200-2200 psi Tip: .011"-.015" Conventional Spray Air Pressure: 60-80 psi Fluid Pressure: 10-20 psi Brush: Use high quality natural china bristle brushes. Roller: Use 1/4" synthetic nap covers.
	Cleanup: Use Anchor #J-1131 or #J-34 Fine Finish Blend.
	Application Considerations: Brush, spray, or roll. Apply in wet coats to avoid dusting. When spraying, use cross-hatch method, overlapping each pass 50%. Clean system thoroughly before and after each use. On a derusted surface the application of a dry film thickness of at least 2 mils is recommended.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.