Product Profile:
 |
General Description:
Safety Zone Striping paint is for use of lining traffic lanes, parking lots, interior
department zoning, or any area that requires high visibility. It dries very fast
and has good resistance to oil, water, salt and abrasion.
|
|
Common Usage:
This product can be applied on concrete, asphalt, brick, wood, or other
surfaces.
|
|
Color: White, Red, Blue and Yellow |
|
Finish: Flat |
Coating Systems:
|
Primer Coats:
Self-Priming. Consult your Anchor representative for specific job
recommendations.
|
Surface Preparation:
|
Surface should be dry and free of contaminants such as excess dirt, grease or oil.
|
Technical Data:
|
Volume Solids: 53.43% -varies by color |
|
Recommended Thickness: 4-6 mils dry. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
25 Minutes |
|
1 Hour |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Zone Marking Coatings |
|
Maximum Allowable V.O.C.: 3.8 lbs./Gallon (450 g/l) |
|
Actual V.O.C.: 3.27 lbs./Gallon (393 g/l) -varies by color |
|
Theoretical Coverage:
2300 Lined Feet @ 4" wide per gallon, assuming no application losses.
Coverage will vary depending on surface texture and application technique.
|
|
Packaging: 55 Gallon drums, 5 Gallon pails, and 1 Gallon cans
|
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110 F |
|
|
Physical Properties:
|
Abrasion: |
|
Very Good |
|
Flexibility: |
|
Very Good |
|
Weather: |
|
Very Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
5.0 |
|
9.4 |
|
171 |
|
Minimum: |
|
4.0 |
|
7.5 |
|
214 |
|
Maximum: |
|
6.0 |
|
11.2 |
|
142 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
|
|
Thinning: Use Anchor #J-1131.
|
|
Surface Temperature:
| Minimum 55 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%.
|
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi |
|
Tip: |
|
.013"-.017" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use a high quality natural china bristle brush. |
|
Roller: Use 1/4" synthetic nap covers. |
|
|
Cleanup: Use Anchor #J-1131. |
|
Application Considerations:
Spray application recommended as this coating dries very fast. Apply in a full
wet coat. This product may be brushed or rolled in small areas.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
