Product Profile:
 |
General Description:
An alkyd based dead flat coating.
|
|
Common Usage:
Primarily on ornamental iron, heaters, or any utility type framing, etc.
This product has good resistance to humidity, fumes, marking, and weather.
|
|
Color: Black |
|
Finish: Flat |
Coating Systems:
|
Primer Coats:
Use Anchor #1730 Rust Inhibitive Primer Series, #472 Fast Dry Primer or direct to metal. Consult your Anchor representative for specific job recommendations. |
Surface Preparation:
|
For maximum performance, the recommended substrate should be blasted in
accordance with SSPC-SP7. If blast cleaning is not feasible, the substrate
should be degreased in accordance with SSPC-SP1. All burrs should be
removed and sharp edges or rough weld seams should be ground down. Full
use should then be made of mechanical power tools, in conjunction with wire
brushing and chipping to remove all loose rust and mill scale to a standard of
cleanliness conforming to SP-2 or SP-3.
|
Technical Data:
|
Volume Solids: 44.94% |
|
Recommended Thickness: 1.6-2.0 mils dry per coat. Two coats recommended. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
20 Minutes |
|
8 hours |
|
| (Cooler temperatures and higher humidity will lengthen drying time) |
|
|
Architectural and Industrial Maintenance Category: Not Intended for Residential Use; Shop Use Only |
|
Actual V.O.C.: 3.61 lbs./gal. (433.2 g/l) |
|
Theoretical Coverage:
721 sq. ft./gallon @ 1 mil dry, assuming no application loss. Coverage will vary depending on the surface texture and application technique. |
|
Packaging: 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans |
|
Storage Temperature:
| Minimum 20 F |
|
Maximum 110 F |
|
|
Chemical Resistance:
|
Alkalis: |
|
Poor |
|
Acids: |
|
Fair |
|
Water: |
|
Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
1.8 |
|
4 |
|
400 |
|
Minimum: |
|
1.6 |
|
3.5 |
|
451 |
|
Maximum: |
|
2.0 |
|
4.5 |
|
360 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can. |
|
Thinning: Thin only if necessary with Anchor #J-1131 for spray applications, use #J-1112 for brush and roller usage. |
|
Surface Temperature:
| Minimum 40 F |
|
Maximum 110 F |
| The surface should be dry and the relative humidity should be less than 85%. |
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi |
|
Tip: |
|
.011"-.015" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
60-80 psi. |
|
|
Fluid Pressure: |
|
10-20 psi. |
|
Brush: Use high quality natural china bristle brushes. |
|
Roller: Use 1/4" synthetic nap covers. |
|
|
Cleanup: Use Anchor #J-1131 synthetic thinner. |
|
Application Considerations:
The recommended method of application is by airless spray. However, brush,
roller, or conventional spray may also be used. To avoid dusting, apply in wet
coats. On a derusted surface the application of a dry film thickness of at
least 2 mils is recommended.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
