General Description: This water reducible alkyd provides fast air dry time, good humidity resistance, excellent salt spray and corrosion resistance. This coating has excellent gloss and color retention, resistance to chalking, staining, and dirt pickup.
	Common Usage: Environ maintenance enamels are designed for equipment, machinery, and metal structures with excellent adhesion to steel.
	Color: White, standard and custom colors.
	Finish: High gloss

Primer Coats: Anchor #2722 Waterborne Rust Inhibitive Primer or #B-7911 Gray High Solids Alkyd Primers. Consult your Anchor representative for specific job recommendations.

Apply only over clean, dry and properly cured surfaces that are free of form release agents, cutting oils, dirt, grease, loose foreign matter and frost. The substrate shall be thoroughly degreased in accordance with SSPC-SP1 standards. All burrs should be removed and sharp edges or rough weld seams should be ground down. All rust and mill scale should be removed as required by SSPC-SP6 surface preparation.

	Volume Solids: 27.69% -varies by color
	Recommended Thickness: 1.6-2.0 mils dry per coat. Two coats recommended.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 1 Hour 4 Hours (Cooler temperatures and higher humidity will require a longer cure time.)
	Architectural and Industrial Maintenance Category: Industrial Maintenance Coatings
	Maximum Allowable V.O.C.: 3.8 lbs./gal. (450g/l)
	Actual V.O.C.: 1.42 lbs./gal. (170 g/l) (3.02 lbs./gal. minus water + exempt materials) - varies by color
	Theoretical Coverage: 445 sq. ft./gallon @ I mil dry, assuming no application loss. Coverage will vary depending on color, surface texture and application technique.
	Packaging: 55 Gallon drums, 5 Gallon pails, and 1 Gallon cans
	Storage Temperature: Minimum 35 F Maximum 110 F
	Physical Properties: Abrasion: Excellent Weather: Excellent Corrosion: Excellent Color: Excellent, very resistant to fading Submersion: Not Recommended
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 1.8 6.5 247 Minimum: 1.6 5.8 278 Maximum: 2.0 7.2 223
	Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
	Thinning: Thin with water, only if necessary.
	Surface Temperature: Minimum 50 F Maximum 90 F
	Application Equipment: Airless Spray Pressure: 1800-2400 psi. Tip: .015 Conventional Spray Air Pressure: 60-80 psi. Fluid Pressure: 10-20 psi.
	Cleanup: Use soap and water.
	Application Considerations: Spray recommended. Do not apply when overnight freeze, rain or dew is forecast. NOTE: During Conditions of high humidity or moist air, allow for a much longer cure time. Warm air, moving over the substrate, will promote drying and improve cure time when less than optimum application conditions exist. On a derusted surface the application of a dry film thickness of at least 2 mils is recommended. Avoid applying Environ products directly on galvanized surfaces.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.