General Description: A high solids, low V.O.C., inorganic zinc-rich primer providing excellent protection from severe environment and exposures. This is a solvent-based inorganic ethyl polysillicate/ 100% zinc catalyst system.
	Common Usage: This primer is widely used in carefully engineered systems, maintenance-free life expectancy of up to twenty years.
	Color: Zinc Gray
	Finish: Flat

Finish Coats: This product is not recommended for immersion in acids, alkalis, or chlorinated hydrocarbons without resistant top coat. Suitable intermediates and topcoats include epoxies, waterbornes, urethanes, acrylics, and silicones. Consult your Anchor representative for specific job recommendations.

The surface should be sandblasted in accordance with SSPC-10 near white metal blast. Remove all flux and scab from welding. Grind smooth all rough welds and sharp edges. Remove any grease, oil or dirt with solvent prior to blasting. The surface should be coated as soon as possible after sandblast.

	Solids Content of Mixed Material By Weight By Volume Cat-O-Zinc 93A&B 88 54
	Recommended Thickness: 2-3 mils dry.
	Drying Time:  Temperature To Touch To Recoat 75 F / 55% R.H. 4 Hours 48 Hours (Cooler temperatures and higher humidity will lengthen drying time)
	Architectural and Industrial Maintenance Category: Metallic Pigmented
	Maximum Allowable V.O.C.: 4.2 lbs./gal. (500 g/l)
	Actual V.O.C.: 3.2 lbs./gal. (384 g/l)
	Theoretical Coverage: 289 sq. ft./ gallon @ 3 mils dry, assuming no application loss. Coverage will vary depending on surface texture and application technique.
	Packaging: Supplied in a .75 gallon kit for easier handling. Available in 5 gallon pails and 1 gallon cans.
	Storage Temperature: Minimum 20 F Maximum 110F
	Chemical Resistance: Alkalis: Not recommended for immersion Acids: Not recommended for immersion Water: Excellent Solvents: Excellent
	Heat Resistance: Up to 750 F
	Health & Safety: Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.
	Mix Ratio: One part 93A to one part 93B
	Pot Life: 4-6 Hours (Keep cool and agitated)

	Coverage Rates Per Coat:  Dry Mils Wet Mils Sq.Ft./Gal. Suggested: 2.5 4.7 346 Minimum: 2.0 3.6 433 Maximum: 3.0 5.6 289
	Mixing: Always mix Zinc Dust into liquid. Hand or mechanically agitate being careful not to mix so fast that air is entrapped. Strain the mixture and place into a mechanically agitated pot.
	Surface Temperature: Minimum 40 F Maximum 90 F The surface should be dry and the relative humidity should be 40-90%.
	Application Equipment: Airless Spray Not recommended for Zinc-Rich applications due to excessive wear on pump and gun. If mandatory, use a Graco 28:1 pump, reverse-a-clean tip with .017-.021 orifice and an agitated material pot. Conventional Spray Air Hose: 5/16" I.D. for Air, 1/2" I.D. for Material Spray Gun: Binks #18 Gun- 67PD Air Cap 66 Nozzle Devilbiss MBC Gun- AV-15-E Fluid Tip MBC-444-E Needle, #704 or #64 Air Cap, Use 25' hoses from pot for best results.
	Cleanup: Use Anchor #J-32 or #J-1131 solvent.
	Application Considerations: Spray preferred. Spray pot should be on the same level or higher than the gun. If application is delayed 10 or more minutes, clear the liquid hose. A mist coat is recommended when topcoating to minimize bubbling.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.