Product Profile:
 |
General Description:
A bitumastic black solution used in general maintenance situations
under moderate corrosive conditions. It can be used over metallic or concrete
surfaces that have been properly cleaned.
|
|
Common Usage:
Specific uses for this product include the coating of pipes, storage tanks and
water submerged tanks.
|
|
Color: Black |
|
Finish: Semi-Gloss |
Coating Systems:
|
Primer Coats:
Self-Priming. Consult your Anchor representative for specific job recommendations. |
Surface Preparation:
|
The substrate shall be cleaned and degreased in accordance with SSPC-SP1.
Concrete should be cured and all laitance removed. All burrs should be
removed and sharp edges or rough weld seams should be ground down. All
surface imperfections should be repaired. Where weathered steel is
applicable and where the substrate has reached rust grade, appropriate
chemical cleaning or blasting will be necessary.
|
Technical Data:
|
Volume Solids: 67% |
|
Recommended Thickness: 3 mils dry. |
|
Drying Time:
| Temperature |
|
To Touch |
|
To Recoat |
|
| 75 F / 55% R.H. |
|
2 Hours |
|
24 Hours |
|
| (Cooler temperatures and higher humidity will require a longer cure time) |
|
|
Architectural and Industrial Maintenance Category: Bituminous Coatings and Mastics |
|
Maximum Allowable V.O.C.: 4.2 lbs./gal. (500g/l) |
|
Actual V.O.C.: 2.3 lbs./gal. (276 g/l) |
|
Theoretical Coverage:
1,075 sq. ft./gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on surface texture and application technique. |
|
Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans. |
|
Storage Temperature:
| Minimum 35 F |
|
Maximum 110 F |
|
|
Chemical Resistance:
|
Alkalis: |
|
Very Good |
|
Acids: |
|
Very Good |
|
Water: |
|
Very Good |
|
|
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product. |
Application:
|
Coverage Rates Per Coat:
|
|
|
Dry Mils |
|
Wet Mils |
|
Sq.Ft./Gal. |
|
Suggested: |
|
3.0 |
|
4.5 |
|
358 |
|
Minimum: |
|
2.0 |
|
3.0 |
|
537 |
|
Maximum: |
|
4.0 |
|
6.0 |
|
269 |
|
|
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can. |
|
Thinning: Thin with Anchor #J-1112. |
|
Surface Temperature:
| Minimum 50 F |
|
Maximum 90 F |
|
|
Application Equipment:
|
Airless Spray
|
Pressure: |
|
1200-2200 psi |
|
Tip: |
|
.013"-.017" |
|
|
Conventional Spray
|
|
|
Air Pressure: |
|
40-70 psi |
|
|
Fluid Pressure: |
|
10-20 psi |
|
Brush: Use a high quality natural china bristle brush. |
|
Roller: Use a 1/4" synthetic nap roller cover. |
|
|
Cleanup: Use Anchor #J-1112 solvent. |
|
Application Considerations:
Spray application recommended. However, brush, roller, or conventional
spray may also be used. To avoid dusting, apply in full wet coats. On a
derusted surface the application of a dry film thickness of at least 3 mils is
recommended.
|
Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.
|
