Click here to open the
Colorizer web-deck color viewer



 
Signature™ Flat Latex Series
5000 Series
<<Back to Data Sheets

Product Profile:
General Description:
This premium vinyl acrylic latex is specially formulated for easy aplication, providing a splatter resistant, high hiding, washable coating that will cover most surfaces in one coat and dries to a silky matte finish.
Common Usage:
This is a premium acrylic latex paint ideal for use on interior walls and ceilings.
Color: White, Standard and Custom colors
Finish: Flat
 
Coating Systems:
Primer Coats:
Prime new sheetrock with Anchor #P-1508 drywall sealer Consult your Anchor representative for specific job recommendations.
 
Surface Preparation:
The surface must be clean, dry, and free of any contaminants. On previously painted surfaces, be sure that stains and imperfections will not bleed through coating. New or old surfaces need not be primed unless variance in color is substantial. Glossy surfaces should be sanded or flattened by use of a chemical deglosser.
 
Technical Data:
Volume Solids: 36.77% -varies by color
Recommended Thickness: 1.6-2.0 mils dry per coat. Two coats recommended.
Drying Time: 
Temperature To Touch To Recoat
75 F / 55% R.H. 30 Minutes 2 Hours
(Cooler temperatures and higher humidity will lengthen drying time)
Architectural and Industrial Maintenance Category: Flat Coatings, Interior
Maximum Allowable V.O.C.: 2.1 lbs./gal. (250g/l)
Actual V.O.C.: .48 lbs./gal. (58 g/l) (1.13 lbs./gal. minus water + exempt materials) - varies by color
Theoretical Coverage:
590 sq. ft./gallon @ 1 mil dry, assuming no application losses. Coverage will vary depending on color, the surface texture and application technique.
Packaging: 55 Gallon drums, 5 Gallon pails, 1 Gallon cans, and quart (1/4 gallon) cans
Storage Temperature:
Minimum 35 F Maximum 110 F
Physical Properties:
Abrasion: Good
Flexibility: Good
Weather: Interior Use Only
Health & Safety:
Refer to the front of this manual, the product label itself, and your Anchor representative concerning a Material Safety Data Sheet for complete information on this product.

Application:
Coverage Rates Per Coat: 
Dry Mils Wet Mils Sq.Ft./Gal.
Suggested: 1.8 4.9 329
Minimum: 1.6 4.4 369
Maximum: 2.0 5.4 295
Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
Thinning: Thin with water only if necessary up to one pint per gallon.
Surface Temperature:
Minimum 50 F Maximum 110 F
The surface should be dry and the relative humidity should be less than 85%.
Application Equipment:
Airless Spray
Pressure: 1800-2400 psi
Tip: .015
Conventional Spray
Air Pressure: 40-70 psi.
Fluid Pressure: 10-20 psi
Brush: Use 1/4
Roller: Use high quality synthetic or nylon bristle brushes.
Cleanup: Use soap and water.
Application Considerations:
Brush, spray or roll. Strain material before spraying. Backroll after spraying. Check color before applying as Anchor can not be responsible for color dissatisfaction after application. Always apply into rather than away from the wet edge, overlapping each pass 50%. Avoid touching up, rolling or brushing back into paint more than ten minutes after applying. Touch up when paint is completely dry. Allow the paint to cure at least ten days before cleaning newly painted surfaces.
Touch Up:
Proper touch-up is accomplished by applying a thin coat of this product over a well coated surface using the same method of application as used to apply the finish coat, that is, spray over spray, roller over roller. If the finish coat is sprayed, it is also possible to spray a small amount into an empty container, then touching up with a foam brush. Touch up should be done within 5 degrees of the original temperature.

Limited Warranty:
The technical data on this label or on other data is true and accurate to the best of our knowledge. We guarantee our products to conform to ANCHOR PAINT MFG. CO. quality control standards. Due to misuse in handling, storage, application and workmanship or variables such as weather or surface integrity that are beyond our control, Anchor Paint does not authorize any representative to make any warranty or merchantability of fitness of this product. Any liability whatsoever of Anchor Paint Mfg. Co. to the buyer or user of this product is limited to the purchaser’s cost of the product itself.

 

<<Back to Data Sheets